Nov 29, 2014 Delving into the 5e DMG Part 2 With Part 1 Master of World we get a full page illustration. Most of the illustration are good but nothing that grabs like the.
The 5e DMG has a short section on “handling mobs:” it has a chart for approximating, out of a group of attacking monsters, how many monsters hit.
It’s pretty simple: subtract attacker’s hit bonus from the target’s AC. Cross-index that number on the chart. If the number is 1-5, all the attackers hit; if it’s 6-12, 1/2 of them hit; etc., up to 1 in 20 of the attackers hitting on a 20.
I ran a big set-piece battle yesterday: 8 mid-level PCs and 10 gnomes against 20+ drow and other assorted creatures, including a drow spider chariot and a sinister angel. With a wizard and a sorcerer PC and two drow wizards, all slinging fireballs, the mob attacks weren’t much of a factor. With all those fireballs, what I COULD have used was rules for mob saving throws.
- Dec 09, 2014 D&D 5E: Quick and Dirty Monsters from the DMG: Nuckelavee The new Dungeon Master's Guide includes two ways to design monsters: the long, hard route which ends up with a fully featured stat block, and the quick and dirty route. So I'm hoping I won't have that problem in 5e. I'm gonna throw this nucklavee at them, and if they beat it, Rocks.
- Taking 10 When your character is not being threatened or distracted, you may choose to take 10. Instead of rolling 1d20 for the skill check, calculate your result as if you had rolled a 10. For many routine tasks, taking 10 makes them automatically successful. Distractions or threats (such as combat) make it impossible for a character to take 10.
If I’d thought about it, I’d have realized that the same chart can be used for saving throws. Instead of subtracting attack bonus from AC, subtract saving throw bonus from DC, and use the chart as normal. For instance, a fireball save DC of 15, minus the drow dex save (+2) is 13, which, according to the chart, means that 1/3 of the drow succeed on their saving throw (and probably survive with 1 or 2 HP left).
In fact, this same chart can be used for ability/skill checks (how many orcs managed to climb the wall? DC minus skill bonus) or any other d20 roll.
To me, it seems this is all you need to run fairly simple battles with dozens or hundreds of creatures per side. The amount of HP tracking is not excessive: for instance, in this unit of 50 ogres, 24 have 15 damage and the other 25 have 30 damage. (For ease of bookkeeping, assume that melee attacks always target the most-damaged creature.)
5e Dmg Take 10 Hours
You might also care about the base size of big units. I assumed that a close-packed formation of 10 Medium troops took up the size of one Large creature. I’d say that 25 troops are Huge and 50 are Gargantuan.
If we do any bigger-scale battles, I might find other rules that I need (after all, the Chain Mail rules are much longer than this blog post) but right now, this is looking pretty good for running big D&D skirmishes.
I'm new to DMing! How do I start?
First, congratulations on running a game! You'll get the hang of it pretty quickly. The easiest way to build an encounter is to pick an enemy from the Monster Manual with a CR around the same as the level of PCs in your party, maybe one higher if you want them to have a tough fight. This won't always be perfect, but it's a good place to start. You'll find that this method mostly generates Medium or Hard difficulty encounters, which is about what you are aiming for.
To spice things up, increase the number of enemies. Either go for a group of lower-level mooks, or a second bad guy of around the same CR, or mix and match. Don't go too wild with this, though - the PCs can only take on so many enemies at once. In 5th Edition, outnumbering your opponent can be quite an advantage. Be very careful before putting your PCs up against a Deadly encounter, especially against lots of enemies.
5e Dmg Take 10 3
Why are my players finding encounters so easy?
5e Dmg Take 10 Days
If you're using this calculator a lot, you may have found it can seem to overstate the difficulty of encounters. First I'll explain why this happens, and then how you can fix this. Dmg office.
Take 10 Menu
The biggest culprit for easy encounters is the party resting too much. If you're like me, your parties tend to have maybe two or three encounters per long rest, often with short rests in between - this makes more sense for some play styles, but causes balance problems.
Dmg file wont open. The way 5th Edition balances resources assumes that parties will have at least a couple of medium-difficulty encounters between each short rest, and maybe two or three short rests between each long rest. This forces characters to be conservative with their limited resources (spell slots, class features, hit dice, and so forth), making each individual encounter tougher. A party that can approach an encounter fresh, with no worries about saving resources, will often find that encounter relatively easy.
How do you fix this? You have two choices.
5e Dmg Take 10 2
- Don't let your party rest as often. There are a couple of ways of doing this - you could have encounters happen closer together without any chance for a break between each (maybe putting the characters on a timer, or make it dangerous to rest), or use the 'Gritty Realism' rest model as described in the DMG (page 267) which makes rests take longer. I have started using Gritty Realism in my games and I've found that it makes designing adventures substantially easier, and stops the party attempting to rest at every opportunity.
- Make the encounters harder. You can probably make the Adjusted Difficulty Rating of an encounter up to double or maybe even triple (for very experienced parties) the XP* rating of a Deadly encounter, and the fight will be more challenging and risky, but not impossible for a prepared party. There are some downsides to this approach, however. Fights become much more dangerous as an encounter can quickly snowball from challenging to deadly if one or two of the PCs are dropped. This is especially pronounced at lower levels where a single hit can be enough to put someone on the floor. If you use this method, you may need to increase the difficulty slowly until you get to the level of challenge you want. *Note for those who use CR, this scales differently. You may only want to increase the CR of encounters by 1 or 2.